Poulan 96194000801 Uživatelský manuál

OWNER'S MANUALMODEL NUMBER:961940008SNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the

10TO MOVE FORWARD AND BACKWARD (See Fig. 15)SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive con

11TO ADJUST SKID PLATES (See Fig. 16)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are located on each

12OPERATIONSNOW THROWING TIPS• Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the ON / OFF switch, to adjust speed.•

13GENERAL REC OM MEN DA TIONSThe warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. To re

14MAINTENANCEAUGER GEAR CASE• The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention

153. Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 lockn

16SERVICE AND ADJUSTMENTS8. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.HINT: Insert a 3/8"

17SERVICE AND ADJUSTMENTSTO REMOVE WHEELS (See Fig. 21)• Remove the klik pin and remove wheel from axle.IMPORTANT: When installing wheel, be sure to

18STORAGEImmediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.WARNING: Never store t

19Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition

2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure

38REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000801AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches. 1 in

39REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000801AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches. 1 in

40NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

4111232301.07.024-BNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M

42REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000801CONTROL PANEL / DISCHARGE CHUTE12345667891111111001.09.001-BKEY PARTNO. NO. DESCRIPTION

43REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000801CONTROL PANEL / DISCHARGE CHUTEKEY PARTNO. NO. DESCRIPTION NOTE: All component dimensio

44REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000801HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use

45REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000801HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use

46REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000801HANDLESKEY PARTNO. NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches.

47REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000801HANDLESKEY PARTNO. NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches.

36. When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impeller and all moving parts have stoppe

48REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000801DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use o

49REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000801DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use o

50REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000801DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use o

51REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000801CHASSIS / ENGINE / PULLEYSKEY PARTNO. NO. DESCRIPTION KEY PARTNO. NO. DESCRIPTION

52REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000801CHASSIS / ENGINE / PULLEYS1011123456798121314141415161718192020212122232401.21.003-BKEY PARTN

53NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

54NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

55REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000801DECALS 1 181037 DECAL, DANGER 3 181035 DECAL, DANGER, DEFLECTOR 4 181042 DECAL, DANGER - -

LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and w

4PARTS PACKED SEPARATELY IN CARTONASSEMBLY / PRE-OPERATIONRead these instructions and this manual in its entirety before you attempt to assemble or op

5ASSEMBLY / PRE-OPERATIONSPEED CON TROL RODSPEED CONTROL BRACKETRETAINER SPRINGSPEED CONTROL LEVERFIG. 2SPEEDCONTROL RODHANDLE KNOBLOWER HANDLEPLASTIC

6ASSEMBLY / PRE-OPERATIONAUGERCONTROL LEVERAUGER CONTROL RODAUGERCONTROL BRACKETRETAINER SPRINGFIG. 6INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)1.

7OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with

8OPERATIONON / OFF switch - used to STOP the engine.Traction drive control lever - used to engage power-pro pelled for ward or reverse motion of snow

9The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glas